The 10L dual planetary mixing mixer is a multifunctional vacuum homogenization mixer. We mass produce various sealants, adhesives, polycarbonate sealants, glass sealants, and inks. Wax products. Designed and manufactured for high viscosity products such as cream and honey latex.
This machine has a beautiful appearance, small size, light weight, and all parts in contact with materials are made of stainless steel (commonly 304, medical 316L); Smooth circular arc transitions are used at all connections inside the pot body, equipped with high-strength material presses, suitable for filling and transferring most viscous materials; The dispersing disk is an intermediate toothed dispersing disk, connected to the spindle of the high-speed dispersing machine. When the spindle of the disperser is running at high speed, the upper and lower parts of the disperser disk are in a rotating state, and a turbulent zone is formed at the edge of 2.5-5mm. The upper and lower serrations of the dispersing disk perform high-speed shearing, impact, crushing, and dispersion of materials such as coatings, paints, dry powders, and solid-liquid mixtures, in order to achieve rapid mixing, dissolution, dispersion, and refinement.

Mixer	Design volume	10L
	Working volume	8L
Low speed mixing system	Stirring power	1.5KW
	Revolution speed	0-65rpm/min
	Rotational speed	0-170rpm/min
	Mixing blade form	Spiral Fried Dough Twists
	Material	304 stainless steel
High-speed decentralized system	Strong dispersion speed	1400rpm/min (adjustable)
	Distributed motor	1.5KW
	Dispersion disk diameter	50mm
	Material	304 stainless steel
Scraping the wall	Quantity	1 group
	Material	SUS304 and Teflon
	Speed	Consistent with the planetary revolution speed
Lifting system	Power up and down	0.37kw
	Elevating height	Be pending
Vacuum system	Vacuum power	0.18kw
	Vacuum degree	≤－0.098Mpa
Jacket	Double layered jacket, can be heated or cooled by water or oil

After completing all the preparation work, turn on the power and proceed with the work according to the prescribed requirements.
The operating components include the main pot mixing system, main pot homogenization system, main pot lifting system, auxiliary pot mixing system, and vacuum pump system. Control can be achieved through buttons on the panel, which can control the illumination and extinguishing of the lighting, the operation of the main pot mixing, the operation of the main pot dispersion, the operation of the vacuum pump, and the heating of the main and auxiliary pots.
Filling operation: a. The filling speed is adjusted by the hydraulic station throttle valve according to the viscosity of the material; b. The filling volume is adjusted by the time setting on the control panel; c. The up button controls the continuous rise of the oil cylinder.

1. Do not operate mixing or dispersion while the lid is open.
2. Do not raise the pot lid too high. Observe while touching the upper limit and lid tightly to ensure safety.
3. Grounding the power supply wire to ensure electrical safety.
4. Before carrying out any maintenance or cleaning, the equipment must be disconnected from the power supply.
5. It is relatively forbidden to put hands into the pot or touch various moving parts during the operation of the equipment to prevent accidents.
6. If there is any abnormal response during operation, stop running immediately and wait to investigate the cause before starting up.

1. Connect the power supply, ensure the power supply matches, and ensure that the ground wire is reliably grounded. Turn on the main power switch, and the power indicator light will turn on.
2. Connect all the pipes and inlet pipes of the pot (connect tap water directly to the inlet), which should be provided by the user.
3. Lift the upper cover by inching, and it can reach a high point after normal operation. When it reaches the top stop of the travel switch, the travel switch will make a clicking sound, and the lifting should stop on its own.
4. Before vacuuming, it is necessary to check whether the pot is flush with the pot cover, whether the pot mouth, material mouth cover, etc. are tightly covered, and whether the seal is reliable. Close all valve interfaces on the pot lid, then open the vacuum valve on the pot lid, and then turn on the vacuum pump to evacuate. After meeting the requirements, turn off the vacuum pump. Please refer to the operating manual for functional instructions, and turn off the vacuum valve at the same time.
5. Disperse cutting and scraper stirring, first add material (which can be replaced by water), and then turn on the corresponding control switches to disperse cutting speed and scraper stirring speed. Disperse the steering wheel to face the cutting wheel and see the reversal; Turn the stirring direction to face the stirring (look up from below) and reverse. During debugging, the homogenizer should be run by tapping and testing, and only after confirming that there are no errors can it be officially put into operation. Before starting the mixing process, it is also necessary to jog and check if there are any abnormalities in the mixing scraper wall. If there are any, they should be eliminated immediately.
6. To open the pot lid and material port lid, it is necessary to do so when there is no vacuum pressure inside the pot. If there is vacuum pressure inside the pot, the valve on the vacuum interface should be closed (and the vacuum pump should be turned off), and the valve on the pot lid should be opened to eliminate vacuum pressure inside the pot.
7. The vacuum pump can be started and operated under the sealing condition of the homogenization pot. If there is a special need to open the air to start the pump, the operation should not exceed 3 minutes.
8. Vacuum pumps are strictly prohibited from operating without oil; It is strictly prohibited to block the exhaust port during pump operation. Before turning off the vacuum pump button, the exhaust valve on the vacuum pipeline must be opened first (to ensure normal pressure in the pipeline and prevent the vacuum pump oil from flowing back into the pipeline).
9. Regularly check the lubricating oil and grease in each component and bearing, and replace them with clean lubricating oil and grease in a timely manner. (It is recommended to use high-temperature resistant lubricating grease.)
10. Keep the mixing slurry and dispersing tray clean. Every time the use or material needs to be stopped or replaced, the parts of the mixing slurry and dispersing disc that come into contact with the working fluid should be cleaned. After the flanges of the pot body and lid are fixed relative to each other, the mixing slurry motor should be started and turned correctly without any other abnormalities before it can be started.
11. All cleaning work for pots is handled by users according to standards. (It is recommended to keep the equipment clean regularly. If there is a prolonged shutdown, it should be cleaned immediately after shutdown.)